Rust inhibitor which penetrates deeply until it reaches the sound metal below.
Drives out moisture and air, stabilising the rust and preventing it from reforming.
Paint and wood stain additive for oil-based paints which improves the flow of paint and eliminates brush marks.
Improves paint adhesion and prevents cracking and peeling.
Improves uniformity and coverage of coat, up to 25% more.

Application tools
    Brush
    Roller
    Airless or HVLP sprayer
    Garden sprayer, pump sprayer

Surface Preparation

Surface preparation when using Owatrol Oil as a rust inhibitor

First, surfaces must be clean, dry and free from oil, grease and other surface contaminants. Remove all scale; loose and flaking rust and old paint back to a sound surface and edge and feather in any sharp edges. Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Severely contaminated surfaces should be cleaned using an appropriate solvent.

Do not remove firm rust or clean the metal back to a bright finish.

Surface preparation when using Owatrol Oil as a paint conditioner

First prepare the surface as per the instructions on your paint can. In addition, if not asked to ensure that you remove all loose and flaking material and treat any organic growth with fungicidal solution or a mix of 1 part water to 1 part chlorine bleach (allow bleach solution to sit for 15 minutes), rinse thoroughly and allow to dry.

Applying Owatrol Oil as a Rust Inhibitor

Using Owatrol Oil on new clean steel:

First prime new steel with a mix of 1 part Owatrol Oil to 3 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on lightly rusted surfaces:

First prime the surface with a mix of 1 part Owatrol Oil to 2 parts primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on new unpainted rusty steel:

First prime the surface with a mix of 1 part Owatrol Oil to 1 part Primer. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Using Owatrol Oil on old, severely rusted or previously coated surfaces:

First, apply wet on wet applications of Owatrol Oil to all exposed rust until fully saturated and allow it to dry. Saturation is indicated by a uniform glossy appearance to the surface when Owatrol Oil is dry. Before Owatrol Oil has hardened, check the surfaces and remove rust scale and old paint loosened by the above. If needed, touch up these areas. Allow to dry. Next, apply a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry. Then follow with normal paint system adding Owatrol Oil to subsequent coats as directed under ‘Mixing instructions’ below.

Note: Owatrol Oil will not lift well-bonded paint.

Applying Owatrol Oil as a Paint Conditioner

First apply paint in normal the manner. If the paint is sticky, drags, sets up to fast or does not level properly add Owatrol Oil (stirring in well) until the paint works smoothly, easily and evenly. Allow the brush, roller or sprayer to be your guide.
Using Owatrol Oil as a Paint Conditioner for wood surfaces in sound condition

First prime any bare wood with a mix of 1 part Owatrol Oil to 2 parts primer and allow to dry. Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below.
Using Owatrol Oil as a Paint Conditioner on damaged, soft or punky wood surfaces

First apply 2 to 4 liberal applications of Owatrol Oil wet on wet, as fast as the wood will absorb it. Do not allow Owatrol Oil to dry between applications. When the wood cannot absorb any more wipe up any excess and allow to dry overnight (12 hrs). Follow with normal paint system adding Owatrol Oil as in ‘Mixing Instructions’ below to ease application and aid adhesion.
Mixing instructions

Topcoat: As required – normally 5 %-20 % by volume.
Undercoat: up to 30 % by volume.
Primer: up to 50 % by volume.

The above is meant as a guide only. Conditions of application, porosity of surface etc. will dictate the amount of Owatrol Oil to be mixed into the paint.
Clean Up

Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Store and maintain equipment as directed by the manufacturer.

NOTE: Any rags, steel wool etc soaked in Owatrol Oil may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing with household waste.
Restrictions

Do not mix or overcoat Owatrol Oil with paints containing hot solvents i.e. Xylene, 2 part coatings, chlorinated rubber etc. – for these type of paints use Owatrol CIP instead. Do not use Owatrol Oil as a paint conditioner in water-based paints, for this purpose use Floetrol instead – Owatrol’s water-based paint conditioner.
Things to Remember

    Cover everything you do not wish to paint.
    Apply between + 5°C and + 35°C.
    Do not apply in direct sunlight or on to hot surfaces.
    Test for compatibility when adding Owatrol Oil to paint.